Local Break Out and Analog Gateway Events, IOS Commands, and Variables#
Local Break Out and Analog Gateway Events
Default IOS Commands |
Notes |
|---|---|
HcsAddIOSDeviceEVT An IOS Device is added. |
|
conf t
voice service VoIP
no IP address trusted authenticate
y
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback
pass-through g711ulaw
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g729r8 bytes 30
codec preference 2 g711ulaw
codec preference 3 g711alaw
end
|
If you are generating the command for VG350 analog gateway, remove y from the generated commands, and then paste it to the analog gateway console. |
Default IOS Commands |
|---|
HcsDeleteIOSDeviceEVT An IOS Device is deleted. |
conf t
no voice service VoIP
no voice class codec 1
end
|
Default IOS Commands |
Available Variables |
|---|---|
HcsAddAnalogGatewayEVT An Analog Gateway is added. |
|
conf t
stcapp ccm-group 1
stcapp
stcapp feature access-code
stcapp feature speed-dial
sccp local {{ pwf.GatewayDAT.networkInterface }}
sccp
bind interface {{ pwf.GatewayDAT.networkInterface }}
sccp ccm group 1
{{ macro.HcsAnalogGwCommandForCCMIdentAndAssocMCR }} ccm-manager
config server {{ fn.one macro.HcsCucmsAssociatedToNDLRMCR}}
ccm-manager sccp local {{ pwf.GatewayDAT.networkInterface }}
ccm-manager sccp
stcapp
end
|
pwf.GatewayDAT.networkInterface - This is the physical device network interface (Ethernet Port) for the analog gateway. |
Default IOS Commands |
Available Variables |
|---|---|
HcsAddAnalogGatewayEndpointEVT An Endpoint is added for the Analog Gateway. |
|
conf t
voice-port {{ pwf.PORT_NUM }}
caller-id enable
timeouts call-disconnect {{ fn.as_string
pwf.GatewayDAT.disconnectTimeout }}
cptone {{ pwf.GatewayDAT.cpTone }}
signal {{macro.HcsIosCmdAnalogGwSignalMCR}}
no shutdown
dial-peer voice {{ pwf.DIAL_PEER_NO }} pots
service stcapp
port {{ pwf.PORT_NUM }}
end
|
pwf.PORT_NUM - This is the FXS port number of the analog gateway device. pwf.GatewayDAT.disconnectTimeout - Time in seconds for which a connection is maintained after the completion of a communication exchange. pwf.GatewayDAT.cpTone - This is the call progress tone of the country that supports each analog device in the gateway. pwf.DIAL_PEER_NO - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Default IOS Commands |
Available Variables |
|---|---|
HcsAddAnalogGatewayEndpointModEVT An Endpoint Module is added for the Analog Gateway. |
|
conf t
voice-port {{ pwf.PORT_NUM }}
caller-id enable
timeouts call-disconnect {{ fn.as_string
pwf.GatewayDAT.disconnectTimeout }}
cptone {{ pwf.GatewayDAT.cpTone }}
signal {{macro.HcsIosCmdAnalogGwSignalMCR}}
no shutdown
dial-peer voice {{ pwf.DIAL_PEER_NO }} pots
service stcapp
port {{ pwf.PORT_NUM }}
end
|
pwf.PORT_NUM - This is the FXS port number of the analog gateway device. pwf.GatewayDAT.cpTone - This is the call progress tone of the country that supports each analog device in the gateway. pwf.GatewayDAT.disconnectTimeout - Time in seconds for which a connection is maintained after the completion of a communication exchange. pwf.DIAL_PEER_NO - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Default IOS Commands |
|---|
HcsDeleteAnalogGatewayEVT An Analog Gateway is deleted. |
conf t
no stcapp
no ccm-manager sccp local {{ input.GatewayDAT.networkInterface }}
no ccm-manager sccp
no sccp
no sccp local {{ input.GatewayDAT.networkInterface }}
no sccp ccm group 1
end
|
Default IOS Commands |
Available Variables |
|---|---|
HcsDeleteAnalogGatewayEndpointEVT An Analog Gateway Endpoint is deleted. |
|
conf t
voice-port {{ pwf.PORT_NUM }}
no caller-id enable
no timeouts call-disconnect
no cptone
no signal
shutdown
no dial-peer voice {{ pwf.DIAL_PEER_NO }} pots
no port {{ pwf.PORT_NUM }}
end
|
pwf.PORT_NUM - This is the FXS port number of the analog gateway device. pwf.DIAL_PEER_NO - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Default IOS Commands |
Available Variables |
|---|---|
HcsDeleteAnalogGatewayEndpointModEVT An Analog Gateway Endpoint Module is deleted. |
|
conf t
voice-port {{ pwf.PORT_NUM }}
no caller-id enable
no timeouts call-disconnect
no cptone
no signal
shutdown
no dial-peer voice {{ pwf.DIAL_PEER_NO }} pots
no port {{ pwf.PORT_NUM }}
end
|
pwf.PORT_NUM - This is the FXS port number of the analog gateway device. pwf.DIAL_PEER_NO - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsAddSipLocalGwEVT A SIP Local Gateway is added. |
|
conf t
voice class e164-pattern-map 4007
e164 \+T
e164 .T
voice service VoIP
allow-connections sip to sip
sip-ua
retry invite 2
timers trying 150
application
service dsapp
param disc-toggle-time 20
param callHold TRUE
param callWaiting TRUE
param callConference TRUE
param callTransfer TRUE
voice translation-rule 802
voice translation-profile VOIPOUT80
translate called 802
voice translation-rule 812
voice translation-profile VOIPIN81
translate calling 811
translate called 812
no voice hunt invalid-number
no voice hunt unassigned-number
[CTD..]
|
Default IOS Commands |
Available Variables |
|---|---|
HcsAddSipLocalGwEVT A SIP Local Gateway is added [CTD] |
|
[CTD]
dial-peer voice 8 VoIP
translation-profile incoming VOIPIN81
session protocol sipv2
incoming called e164-pattern-map 4007
fax rate 14400
no vad
voice translation-rule 812
rule 97 /^\\+01\\(.*\\)/ /904\\1/
rule 98 /^\\+1\\(.*\\)/ /901\\1/
rule 99 /^\\+\\(.*\\)/ /902\\1/
rule 100 /^\\(.*\\)/ /904\\1/
voice translation-rule 9011
rule 98 /^\\+{{pwf.COUNTRYCODE}}\\(.*\\)/ /\\1/ type any
national
rule 99 /^\\+\\(.*\\)/ /\\1/ type any international
rule 100 /^\\(.*\\)/ /\\1/ type any unknown
voice translation-rule 9021
rule 81 /^901\\(.*\\)/ /\\1/ type any national
rule 82 /^902\\(.*\\)/ /\\1/ type any international
rule 83 /^903\\(.*\\)/ /\\1/ type any unknown
rule 84 /^904\\(.*\\)/ /\\1/ type any unknown
voice translation-rule 9022
rule 81 /^901\\(.*\\)/ /{{pwf.STDACCESSPREFIX}}\\1/ type any unknown
rule 82 /^902\\(.*\\)/ /{{pwf.INTLACCESSPREFIX}}\\1/ type any unknown
rule 83 /^903\\(.*\\)/ /\\1/ type any unknown
rule 84 /^904\\(.*\\)/ /\\1/ type any unknown
voice translation-rule 9111
[CTD...]
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Default IOS Commands |
Available Variables |
|---|---|
HcsAddSipLocalGwEVT A SIP Local Gateway is added [CTD] |
|
[CTD]
rule 1 /^\\(.*\\)/ /\+{{pwf.COUNTRYCODE}}\\1/ type national unknown
rule 2 /^\\(.*\\)/ /\+\\1/ type international unknown
voice translation-rule 9012
rule 98 /^\\+{{pwf.COUNTRYCODE}}\\(.*\\)/
/{{pwf.STDACCESSPREFIX}}\\1/ type any unknown
rule 99 /^\\+\\(.*\\)/ /{{pwf.INTLACCESSPREFIX}}\\1/ type any unknown
rule 100 /^\\(.*\\)/ /\\1/ type any unknown
voice translation-rule 9121
voice translation-rule 9112
rule 1 /^{{pwf.INTLACCESSPREFIX}}\\(.*\\)/ /\+\\1/ type unknown unknown
rule 2 /^{{pwf.STDACCESSPREFIX}}\\(.*\\)/
/\+{{pwf.COUNTRYCODE}}\\1/ type unknown unknown
voice translation-rule 9122
voice translation-profile POTSOUT9011
translate calling 9011
translate called 9021
voice translation-profile POTSOUT9012
translate calling 9011
translate called 9022
voice translation-profile POTSOUT9021
translate calling 9012
translate called 9021
voice translation-profile POTSOUT9022
translate calling 9012
translate called 9022
voice translation-profile POTSIN9111
translate calling 9111
translate called 9121
voice translation-profile POTSIN9112
translate calling 9111
translate called 9122
voice translation-profile POTSIN9121
translate calling 9112
translate called 9121
voice translation-profile POTSIN9122
translate calling 9112
translate called 9122
end
|
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsAddSipLocalGwDialPeerEVT Triggers IOS Commands for each Dial Peer when A SIP Local Gateway is added. |
||
conf t
dial-peer voice {{pwf.DIALPEER}} VoIP
translation-profile outgoing VOIPOUT80
{{pwf.PREFERENCE}}
voice-class codec 1
service dsapp
voice-class sip options-keepalive up-interval 120 down-interval
60 retry 2
session target {{pwf.PBXIP}}
destination e164-pattern-map 4007
session protocol sipv2
modem passthrough nse codec g711ulaw
dtmf-relay rtp-nte
fax rate 14400
no vad
end
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
One command set is generated per dial peer. |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsDeleteSipLocalGwEVT A SIP Local Gateway is deleted. |
|
conf t
no voice translation-profile POTSIN9122
no voice translation-profile POTSIN9121
no voice translation-profile POTSIN9112
no voice translation-profile POTSIN9111
no voice translation-profile POTSOUT9022
no voice translation-profile POTSOUT9021
no voice translation-profile POTSOUT9012
no voice translation-profile POTSOUT9011
no voice translation-rule 9122
no voice translation-rule 9112
no voice translation-rule 9121
no voice translation-rule 9012
no voice translation-rule 9111
no voice translation-rule 9022
no voice translation-rule 9021
no voice translation-rule 9011
no voice translation-rule 812
no voice translation-rule 802
no dial-peer voice 8 VoIP
no voice class e164-pattern-map 4007
application
no service dsapp
no sip-ua
voice service VoIP
no allow-connections sip to sip
end
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsDeleteSipLocalGwDialPeerEVT Triggers IOS Commands for each Dial Peer when A SIP Local Gateway is deleted. |
||
conf t
no dial-peer voice {{pwf.DIALPEER}} VoIP
end
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
One command set is generated per dial peer. |
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsUpdateSipLocalGw1EVT Triggers IOS Commands when A SIP Local Gateway is updated. |
||
conf t
no dial-peer voice {{pwf.DIALPEER}} VoIP
end
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Removes configuration related to previous dial peer. One set of commands per dial peer. Note: If "Enable Command Builder" is updated from False to True, IOS commands will be regenerated for the SIP Local Gateway. |
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsUpdateSipLocalGw2EVT Triggers IOS Commands when A SIP Local Gateway is updated. |
||
conf t
dial-peer voice {{pwf.DIALPEER}} VoIP
translation-profile outgoing VOIPOUT80
{{pwf.PREFERENCE}}
voice-class codec 1
service dsapp
voice-class sip options-keepalive up-interval 120 down-interval
60 retry 2
session target {{pwf.PBXIP}}
destination e164-pattern-map 4007
session protocol sipv2
modem passthrough nse codec g711ulaw
dtmf-relay rtp-nte
fax rate 14400
no vad
end
|
pwf.COUNTRYCODE - returns the Country Code based on the Country field configured on this SIP Local GW pwf.STDACCESSPREFIX - returns the Country’s national trunk access prefix based on the Country field configured on this SIP Local GW pwf.INTLACCESSPREFIX - returns the Country’s international access prefix based on the Country field configured on this SIP Local GW pwf.PBXIP - returns the CUCM Server’s IP or hostname for dial peer pwf.PREFERENCE - returns the CUCM server’s priority in the dial peer list pwf.DIALPEER - returns the dial peer number we use to generate dial peer. It starts from 4 for the first dial peer, and increase by 1 for the next one. |
Adds configuration related to new dial peer. One set of commands per dial peer. Event is triggered only if the SIP Trunk information has been updated. |
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsSipLocalGwAddSiteAreaCodeEVT Triggers IOS commands for Area Code when a SIP Local Gateway is associated with a Site. |
||
conf t
voice translation-rule 9021
rule {{pwf.RULENUMBER}} /^901{{pwf.NATCODE}}\\(.*\\)//
{{pwf.NATCODEFORLOCALDIALING}}\\1/ type any subscriber
voice translation-rule 9022
rule {{pwf.RULENUMBER}}
/^901{{pwf.NATCODE}}\\ (.*\\)//{{pwf.NATCODEFORLOCALDIALING}}\\1/
type any unknown
end
|
{{pwf.RULENUMBER}} and {{pwf.NATCODE}} are sequence numbers and area codes that is substituted by workflow during runtime {{pwf.NATCODEFOR LOCALDIALING}} is the Area Code if the administrator selected the "Area Code Used for Local Dialing" option when deploying the site dial plan. If this option was not selected, this variable has no value. |
The workflow for this event generates IOS Commands for each Area Code defined for the associated Site. |
(Provider deployment)
Default IOS Commands |
Available Variables |
Notes |
|---|---|---|
HcsSipLocalGwDelSiteAreaCodeEVT Triggers IOS commands for Area Code when a SIP Local Gateway is disassociated from Site. |
||
conf t
no voice translation-rule 9021
no rule {{pwf.RULENUMBER}}
end
conf t
no voice translation-rule 9022
no rule {{pwf.RULENUMBER}}
end
|
{{pwf.RULENUMBER}} is substituted as sequence number by workflow during run time |
The workflow for this event generates IOS Commands for each Area Code defined for the disassociated Site. If Area Codes are shared across multiple sites and associated with the same gateway, the commands are generated only when the gateway is disassociated from the last site that shares the Area Code. |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwAddSitePstnEVT Triggers IOS commands for PSTN when a SIP Local Gateway is associated with a Site. |
|
conf t
voice translation-rule 9111
rule 3 /^\\(.*\\)/ /{{pwf.PSTNACCESSPREFIX}}\\\\1/ type
subscriber unknown
rule 4 /^\\(.*\\)/ /{{pwf.PSTNACCESSPREFIX}}\\\\1/ type unknown
unknown
voice translation-rule 9112
rule 3 /^\\(.*\\)/ /{{pwf.PSTNACCESSPREFIX}}\\\\1/ type unknown
unknown
end
|
pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site |
(Provider deployment)
Default IOS Commands |
Notes |
|---|---|
HcsSipLocalGwDelSitePstnEVT Triggers IOS commands for PSTN when a SIP Local Gateway is disassociated from Site. |
|
conf t
no voice translation-rule 9111
no rule 3
no rule 4
no voice translation-rule 9112
no rule 3
end
|
By default, these commands are not generated to avoid deleting the voice translation rule for PSTN if the gateway is shared by multiple sites. If you need to delete the translation rules for PSTN when SIP Local Gateway is disassociated from site, clone the command builder template and set the Enabled flag. |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwAddE164AssociationEVT Triggers IOS commands for SIP Local Gateway when an E164 Association (N to 1 DN) is made. |
|
conf t
voice translation-rule 9011
rule {{ pwf.RULENUMBER }} /^{{pwf.DNESCAPE }}{{ pwf.DNPREFIX }}
\\\\ ({{ pwf.RGMASK }} \\\\ )/ /{{ pwf.DDIPREFIX }} \\\\ 1/ type
any national
voice translation-rule 9012
rule {{ pwf.RULENUMBER }} /^{{pwf.DNESCAPE }}{{ pwf.DNPREFIX }}
\\\\ ({{ pwf.RGMASK }} \\\\ )/ /{{ pwf.STDACCESSPREFIX }}{{
pwf.DDIPREFIX }} \\\\ 1/ type any unknown
voice translation-rule 802
rule {{ pwf.RULENUMBER }} /^{{pwf.DNESCAPE }}{{ pwf.DNPREFIX }}
\\\\ ({{ pwf.RGMASK }} \\\\ )/ /\+{{ pwf.COUNTRYCODE }}{{
pwf.DDIPREFIX }} \\\\ 1/
voice translation-rule 9121
rule {{ pwf.RULENUMBER }} /^{{ pwf.DDIPREFIX }} \\\\ ({{
pwf.RGMASK }} \\\\ )/ /{{ pwf.DNPREFIX }} \\\\ 1/ type national
unknown
voice translation-rule 9122
rule {{ pwf.RULENUMBER }} /^{{ pwf.STDACCESSPREFIX }}{{
pwf.DDIPREFIX }} \\\\ ({{ pwf.RGMASK }} \\\\ )/ /{{ pwf.DNPREFIX
}} \\\\ 1/ type unknown unknown
voice translation-rule 712
[CTD..]
|
pwf.DNPREFIX - Contains the directory number prefix (DN without the mask digits) pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site |
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwAddE164AssociationEVT Triggers IOS commands for SIP Local Gateway when an E164 Association (N to 1 DN) is made. |
|
[CTD..]
rule {{ pwf.RULENUMBER }} /^{{ pwf.PSTNACCESSPREFIX }}{{
pwf.STDACCESSPREFIX }}{{ pwf.DDIPREFIX }} \\\\ ({{ pwf.RGMASK }}
\\\\ )/ /{{ pwf.DNPREFIX }} \\\\ 1/
end
|
pwf.RULENUMBER - Contains the appropriate rule index for associate/disassociate |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwDelE164AssociationEVT Triggers IOS commands for SIP Local Gateway when an E164 Association (N to 1 DN) is deleted. |
|
conf t
voice translation-rule 9011
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9012
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 802
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9121
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9122
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 712
no rule {{ pwf.RULENUMBER }}
end
|
pwf.DNPREFIX - Contains the directory number prefix (DN without the mask digits) pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site pwd.RULENUMBER - Contains the appropriate rule index for associate/disassociate |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwAddMultiE164AssociationEVT Triggers IOS commands for SIP Local Gateway when an E164 Association (N to N DN) is made. |
|
conf t
voice translation-rule 9011
rule {{ pwf.RULENUMBER }} /^{{ pwf.DNESCAPE }}{{ pwf.DN }}/ /{{
pwf.DDIPRIMARY }}/ type any national
voice translation-rule 9012
rule {{ pwf.RULENUMBER }} /^{{ pwf.DNESCAPE }}{{ pwf.DN }}/ /{{
pwf.STDACCESSPREFIX }}{{ pwf.DDIPRIMARY }}/ type any unknown
voice translation-rule 802
rule {{ pwf.RULENUMBER }} /^{{ pwf.DNESCAPE }}{{ pwf.DN }}/ /\+{{
pwf.COUNTRYCODE }}{{ pwf.DDIPRIMARY }}/
voice translation-rule 9121
rule {{ pwf.RULENUMBER }} /^{{ pwf.DDIPREFIX }}{{ pwf.RGMASK }}/
/{{ pwf.DN }}/ type national unknown
voice translation-rule 9122
rule {{ pwf.RULENUMBER }} /^{{ pwf.STDACCESSPREFIX }}{{
pwf.DDIPREFIX }}{{ pwf.RGMASK }}/ /{{ pwf.DN }}/ type unknown
unknown
voice translation-rule 712
rule {{ pwf.RULENUMBER }} /^{{ pwf.PSTNACCESSPREFIX }}{{
pwf.STDACCESSPREFIX }}{{ pwf.DDIPREFIX }}{{ pwf.RGMASK }}/ /{{
pwf.DN }}/
end
|
pwf.DN - Contains the directory number pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPRIMARY - Contains the primary E.164 associate with the N:1 association (DDI without + prefix and country code) Note: this still contains the national code (area code) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site pwd.RULENUMBER - Contains the appropriate rule index for associate/disassociate |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HcsSipLocalGwDelMultiE164AssociationEVT Triggers IOS commands for SIP Local Gateway when an E164 Association (N to N DN) is deleted. |
|
conf t
voice translation-rule 9011
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9012
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 802
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9121
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9122
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 712
no rule {{ pwf.RULENUMBER }}
end
|
pwf.DN - Contains the directory number pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPRIMARY - Contains the primary E.164 associate with the N:1 association (DDI without + prefix and country code) Note: this still contains the national code (area code) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site pwd.RULENUMBER - Contains the appropriate rule index for associate/disassociate |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HscSipLocalGwAddVoiceMailPilotNumberEVT Associate a Voice Mail Pilot Number with a Site |
|
conf t
voice translation-rule 9121
rule {{ pwf.RULENUMBER }} /^{{ pwf.DDIPREFIX }}\\\\({{
pwf.RGMASK }}\\\\)/ /{{ pwf.DNPREFIX }}\\\\1/ type national
unknown
voice translation-rule 9122
rule {{ pwf.RULENUMBER }} /^{{ pwf.STDACCESSPREFIX }}{{
pwf.DDIPREFIX }}\\\\({{ pwf.RGMASK }}\\\\)/ /{{ pwf.DNPREFIX
}}\\\\1/ type unknown unknown
end
|
pwf.DNPREFIX - Contains the voice mail pilot number prefix (without the mask digits) pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site pwd.RULENUMBER - Contains the appropriate rule index for voice mail pilot association |
(Provider deployment)
Default IOS Commands |
Available Variables |
|---|---|
HscSipLocalGwDelVoiceMailPilotNumberEVT Disassociate a Voice Mail Pilot Number from a Site |
|
conf t
voice translation-rule 9121
no rule {{ pwf.RULENUMBER }}
end
conf t
voice translation-rule 9122
no rule {{ pwf.RULENUMBER }}
end
|
pwf.DNPREFIX - Contains the voice mail pilot number prefix (without the mask digits) pwf.DNESCAPE - Contains a backslash escape character if the DNPREFIX contains a + pwf.RGMASK - Contains the range mask for prefix (for example if range is 100, then the value is ..) pwf.DDIPREFIX - Contains the DDI (E.164) prefix (DDI without + prefix, country code, or mask digits) Note: this still contains the national code (area code) pwf.STDACCESSPREFIX - National Trunk Prefix for the country associated with the site pwf.COUNTRYCODE - Country Code for the country associated with the site pwf.PSTNACCESSPREFIX - PSTN breakout associated with the country associated with the site pwd.RULENUMBER - Contains the appropriate rule index for voice mail pilot association |