Model: data/InternalNumberInventory

Cisco UCM/Dedicated Instance

There are a few considerations specific to the number inventory when used in a Cisco UCM/Webex Dedicated instance environment.

Vendor and Internal Number Type fields in the inventory:

• Vendor – this field will be blank or Cisco, depending on how the numbers are loaded
• Internal Number Type – this field is not used in UCM or Dedicated instance deployments

Partition and Cluster

The Automate number inventory is not partition or cluster aware. If the same numbers are used multiple times but in different partitions, then these all map to the same number. This should be considered when thinking about the hierarchy level at which the number inventory exists.

Since the number inventory isn't cluster aware, if the same number exists on different clusters, this will map back to the same inventory value unless numbers are assigned to the site level.

Cisco-Microsoft Hybrid Number Inventory

The notes in this section apply if you're using Automate's Cisco-Microsoft hybrid feature for integrated services:

A Cisco-Microsoft hybrid setup is an integration of Cisco and Microsoft capability, where Microsoft calls are routed via Cisco UCM.

In a hybrid setup, the Internal Number Inventory (INI) can be set up in 2 ways:

• E164 number based, for example:

  • an INI entry 3334567 is mapped to an external number of +15553334567.
  • The number 3334567 is set up in Cisco (along with routing for the mapped external number).
  • The number +15553334567 is set up in Microsoft as the line.
  • The numbers 3334567 and +15553334567 should be seen as the same number from an INI tracking perspective.

• Internal number based (site code+extension or just extension)

  • an E164 number is generated by adding a prefix (+88800) to the internal number for setup in Microsoft.

    Note

    The named macro called MultiVendorLine-InternalExt-E164Prefix is used to store the prefix - currently set to +88800.

  • For example, 3334567 is set up as an internal number for the user and no external number is mapped. The line is selected in the Hybrid setup. Then the prefix is added, so the number +1888003334567 is the number in MS Teams for that user.

  Important

  The numbers 3334567 and +888003334567 should be seen as the same number from an INI tracking perspective. The mapping is also reflected in the Run the Directory Number Inventory Audit Tool. In this case, an update of the inventory takes place so that these are not counted as two separate numbers.

The table below summarizes the Number Inventory data for these cases:

For details on the service type scenarios, see Multi Vendor Service Definitions in the Core Feature Guide.

Footnote

Details and Usage

Selecting a specific number from the Number Inventory list view, opens the details view for that number.

The Number Details tab shows read only details for the number, for example Internal Number, Status, Usage, as well as editable fields such as Tag, Description, Reservation Notes, etc. In the case of Cisco-Microsoft hybrid entries, the vendor added would be "Cisco, Microsoft".

The Usage tab provides links to all instances where the number is used.

• In the case of Cisco-Microsoft hybrid usage, the last vendor added would be appended, as seen above in the "Device, User" instances.

• In the case of Webex App Calling usage, the link directs to the Webex App user.

  See Webex App in the Core Feature Guide.

Related Topics

Webex App in the Core Feature Guide.

Microsoft Teams Deployments

The use of the inventory and how it is maintained or managed can differ depending on the types of numbers in your environment. The following is some guidance and best practices to consider for the different number types. If you have a mix of number types, then consider the notes for different number types.

Vendor and Internal Number Type fields in the inventory:

General Notes

The hierarchy consideration is a key section in this chapter to read in planning for numbers in the inventory. Often the numbers are meant to be used in specific sites or regions only due to agreements or emergency services requirements. This is the business context which the Automate number inventory can provide when the numbers are loaded into the inventory at the appropriate hierarchy level. It is often found, after adding Automate to an existing environment, that we identify various numbers that have been incorrectly assigned previously and allow them to be corrected. Any numbers that were added to the Automate inventory through the sync/audit process will likely require moving to the correct hierarchy level. You can find more information related to the specific numbers types below.

This section covers specific logic related to creating and managing the inventory in relation to specific number types in the Microsoft environment. In Automate you can mix and match the types for different needs, so one or more of the sections may apply.

Direct Routing

In this type of setup, you are getting ranges of numbers outside the Microsoft framework from one or more providers. For these number types, the Microsoft tenant only knows about the numbers that you have assigned to users/services. The tenant has no knowledge of the ranges or available/unused numbers.

So the VOSS number inventory capability can only auto-populate the inventory from a sync/audit with those used numbers discovered from the tenant. In this scenario, you will need to load the available numbers into the VOSS Automate number inventory to be managed and available for administrators to assign going forward.

Guidelines for this setup:

• You can preload the ranges of numbers you own ahead of any overbuild process that will sync/audit the inventory. In this case, the system will update the inventory as part of the sync/audit process to mark assigned numbers used. It will still add any used numbers it discovered form the tenant if there were any missed in the preload process.
• You can load the full ranges after the overbuild process – this will fill in the inventory around the used numbers that were discovered and auto created in the inventory from the tenant. You may need to move the created numbers to a different hierarchy level depending on your needs (intermediate node, moving to site/customer). When you load the ranges after the sync/overbuild, the system will fill in the gaps by adding numbers as available that are missing in the inventory while leaving the ones added via the sync/audit process alone.
• Any future ranges you add to the system beyond the initial overbuild will need to be added to VOSS Automate to be available for administrators to use.

Operator Connect and Calling Plan numbers

In this type of setup, you are getting ranges facilitated by the Microsoft Teams framework. For these types of numbers, the Microsoft tenant is fully aware of the ranges of numbers available as they are populated into the system by Microsoft (Calling Plans) or the selected Provider (Operator Connect). So it is important to note the numbers can only actually be used (e.g assigned to a user) when the numbers are available in the Microsoft Tenant post ordering – from Microsoft (Calling Plan) or the selected Provider (Operator Connect). If you add them to the Automate inventory and try to allocate them before they are present in the tenant, you will get an error message about the numbers not existing in the tenant.

Currently, the data we receive from the Microsoft tenant about the numbers does not provide any information regarding how the numbers are to be used - e.g site specific, etc.

The hierarchy recommendations earlier in this chapter should be referenced and numbers should be loaded according to how the numbers are ordered and registered with Microsoft or the Provider (e.g site specific, global, etc).

The best practice recommendation to streamline the inventory management of these number types is:

• Number ranges are loaded into the Automate number inventory at the appropriate hierarchy before they're synced in from the Microsoft tenant

• This ensures that the numbers are at the correct hierarchy level and context in the system for use in the system - that users and services can only be assigned appropriate numbers.

  Important

  New Calling Plan numbers cannot be assigned to users unless an emergency location is set.

  To set the emergency location for new Calling Plan numbers:

  1. Navigate to the relevant customer or site hierarchy and select the Subscriber Management > Advanced > Emergency Location Ops Tool menu.
  2. On the Ops Tool form, verify that the Number Type is set to CallingPlan.
  3. Select an Emergency Location from the dropdown.
  4. Click Save to update the emergency location of the numbers at this hierarchy where this has not been set.

• When the sync/audit process completes, the system updates those inventory entries with status, usage, type, etc., and won't move them.

Automate can generate inventory entries for numbers of these types. However, there are some considerations and for this reason it is recommended to preload the numbers for improved accuracy and ease of use.

The following are considerations of the generated inventory and potential actions if the sync/audit was run before you loaded your inventory:

• It will generate inventory entries for numbers assigned to users/services in the tenant only. We do this for assigned numbers to ensure they are at least captured and since they are assigned there is not a risk of being assigned incorrectly.
• Numbers that are not assigned will not be generated in the inventory. This is to avoid available numbers being created at the wrong place in the hierarchy and inadvertently being assigned to users in the wrong sites, etc.
• It will create the generated inventory entries at the same hierarchy level as the tenant details (typically customer). Typically, they are required at a different level in the hierarchy and they will need to be moved after this creation.
• The ranges will need to be loaded to create the available numbers in the range within the inventory so they are available to be assigned to users/services. You can just load the whole range and the system will fill in the blanks, creating inventory entries for missing numbers while leaving existing numbers (created by the sync) alone.

You can look at the number data provided by Microsoft for these number types by reviewing the device/msteamsonline/Number device model. Note - these model instances will always be at the same level as the tenant - they do not get moved around and are completely independent of the inventory entries for the numbers.

Webex Calling

This section describes number inventory handling in a Webex Calling environment. Key considerations in a Webex Calling environment include:

• In a Webex Calling environment, resources all reside in locations including numbers regardless of the source (for example, CCP, non-integrated CCP, or Cisco).
• PSTN numbers must be loaded into Webex as available numbers before they can be used/assigned to users. This process can vary depending on how you're sourcing the numbers - for example, CCP, or Cisco Cloud. For this reason, the numbers are typically already in Webex - to pull into the Automate system and inventory.

From the Number Range Management menu at a site:

• For numbers and ranges of numbers, Starting Extension and Ending Extension number values must be prefixed with + and are then created and maintained in VOSS Automate with the prefix format \+. When adding numbers, this can also be seen in the Transaction detail.

• Vendor – this field will typically be Webex Calling. If they are not loaded with this value initially, the system will update the numbers as they are allocated to vendor Webex Calling.

  Note

  Numbers can be pushed to the Webex Control Hub when adding number ranges at site level with the Vendor set as Webex Calling.

• If the Operation is Add:

  When adding numbers and selecting the Vendor as Webex Calling, a Webex Control Hub panel displays the options if:

  1. The Webex App is configured at the customer hierarchy.

See the Webex App chapter in the Core Feature Guide.

2. The available macro WebexCallingNumberMgmtEnabledSite has not been cloned to the site and set to value False. (If required, this task can be carried out if Webex Calling number management should be disabled for a site.)

   The options are:

   • Push Numbers to Webex: this allows for numbers to be added to the site in VOSS Automate and to the Webex Control Hub. (Refer to the Create Spark Number action in the Transaction list.)

   • Push as Active: dependent on the option Push Numbers to Webex set to enabled.

     If enabled and Push Numbers to Webex is enabled, numbers are added in VOSS Automate INI added as Status of Available, and on Webex Control Hub created as Active.

     If disabled and Push Numbers to Webex is enabled, numbers are added in both VOSS Automate INI and the Webex Control Hub as Inactive.

     Number extensions are added to the INI when a user is assigned a number and an extension is then added.

• If the Operation is Modify:

  This operation can be used on selected numbers that are in Status of Inactive - to set them as:

  • Active in the Webex Control Hub. Refer to the Activate Spark Number action in the Transaction list.
  • Status is Available in the VOSS Automate INI.

• If the Operation is Delete:

  Selected numbers are deleted from VOSS Automate INI and the Webex Control Hub. Refer to the Delete Spark Number action in the Transaction list.

• Internal Number Type – this field is used to reflect the type of number in the Webex environment. If you are adding or activating numbers via Number Range Management then the type is Phone Number. Any numbers marked as Extension have been synced in from the Webex Control Hub.

Since the numbers are known in the Webex environment, as well as the Locations for use, the VOSS Automate system will generate the inventory based on the data from Webex. This includes:

• The sync process handles the creation of inventory entries in the Automate platform as numbers are pulled in. You should ensure the sync process handles Locations in Webex prior handling numbers (out of the box syncs ensure this).
• During a site handling Webex Locations, if a corresponding Automate site does not exist, Automate will create a site.

See the Webex Location Node Mapping topic in the Core Feature Guide for more details on Site to Location mapping for Webex for more details on how they are aligned.

• When Webex numbers are synced into Automate, the prefix format \+ is used. Any inventory entries that don't exist are created in the Automate site corresponding to the Webex Location. This includes PSTN numbers and also internal-only extensions.
• The internal number in the Automate number inventory uses the PSTN number (if it has one); or it uses the extension number, if that is the only data available.
• For PSTN numbers, the extension (if there is one) is also captured in the number inventory record via the Extension field.
• Removal of numbers
• Typically, inventory audit functionality won't be required if good sync practices are followed, as the inventory changes are handled through the sync process.

Number Reservation

Numbers can be reserved for future use. For example, for users who will soon be joining the company. When a number is reserved, it is unavailable and can't be allocated to a subscriber, phone, device, etc.

Number Cooling

Numbers can be placed into a cooling period, either manually or automatically. When automated number cooling is enabled, numbers are placed into cooling for a predefined period when the subscriber or phone associated with the number is deleted.

While the number is in its cooling period, it is unavailable and can't be allocated, for example, to a subscriber, phone, or device.

A number is released from cooling and is available for use when:

• The cooling period reaches its end date
• It is manually released from the cooling period

Number Inventory entries - End-user Provisioning Tasks

The number inventory is integrated into various features in the system to:

1. Display options of numbers for selecting/assignment across the system. The numbers presented for selection follow rules specific to the feature in many cases, for instance can lines be shared or not, etc.
2. Manage the state of the numbers in the inventory via the workflows - marking the number used, available, and updating other managed fields depending on the MACD being performed. This includes any specific logic setup for the un-managed fields. See the section on flexibility for options to control the update that occurs.

Related Topics

• Number Status and Usage
• Number Cooling
• Number Reservation
• Number Inventory Alerting

AudioCodes Device Number Integration in the Core Feature Guide