Called Party Number As Dialed Feature
-------------------------------------

By default Cisco Type 1-4 dial plans route outbound PSTN calls with called party
numbers in a +E.164 format. However, you can implement the As Dialed feature to
instead route outbound calls using an 'as-dialed' format using a country's
national trunk prefix.

For example, for Great Britain, if the dialed number is 0 20 8824 9286, then
called-party number in E.164 format is +44 20 8824 9286. If the 'as-dialed'
format is enabled, then the called-party number is 0 20 8824 9286.

.. note::

* Enabling sending called-party numbers 'as dialed' is done on a per-country
and per-call type basis.
* This procedure applies to Cisco Type 1-4 dial plan schema groups.

The procedures to implement the Called-Party Number As Dialed feature vary
depending on:

* The version of VOSS-4-UC
* Whether country-specific dial plans have been deployed to the customer

Edit Country Dial Plan Schema [pre-10.6(2)] for Called-Party As Dialed Feature
..............................................................................

Modify the Route Patterns and Route Lists in the dial plan schema for each country
dial plan to be deployed to the customer.

.. important::

Edit all route patterns with the following exceptions:

* Any route pattern that has the digits 04 (emergency), 05 (service), or 11
(operator) immediately before the dot.
* Any route pattern that has the digits 01 (international) immediately before
the dot, unless the country code is specified immediately after the dot.
* Any route pattern that has an X (mask digit) immediately after the dot.

Edit all route lists with the following exceptions:

* Emergency
* International
* Operator
* Service

Before You Begin
................

To complete this procedure, you need to know the country code and country-specific
trunk prefix.

1. Log in as provider administrator.
#. Select **Dial Plan Management > Advanced Configuration > Dial Plan Schema**.
#. Click the country dial plan schema you want to modify.

Select the country dial plan schema located closest to the customer hierarchy node.

Example: For Great Britain, select HcsGenericCustomerGBRDP-V5-SCH.

#. Select the **Route Patterns** tab.
#. For each route pattern, except for the ones noted previously:

a. In the Route Pattern field:

* If the route pattern contains the country code after the dot, move it to
immediately before the dot.
* If the route pattern does not contain the country code, add it immediately
before the dot.

Example: For Great Britain:

* Change \**001.44! to \**00144.!
* Change \**002.! to \**00244.!

b. In the Called Party Prefix Digits (Outgoing Calls) field, change the + to
+<cc>, where <cc> is the appropriate country code.

Example: For Great Britain, change + to +44

6. Select the **Route Lists** tab.
#. For each route list, except for the ones noted previously, under Members, click **More...**

a. If necessary, click + to expand the Members field.
b. For Called Party Discard Digits, select PreDot.
c. For Called Party Prefix Digits (Outgoing Calls), enter the appropriate trunk
prefix for the country.

8. Click **Save**.

Edit Country Dial Plan Schema [10.6(2) or later] for Called-Party As Dialed Feature
...................................................................................

Modify the dial plan schema for each country dial plan to be deployed to the customer.

.. important::

Edit all route lists with the following exceptions:

* Emergency
* International
* Operator
* Service

Before You Begin
................

To complete this procedure, you need to know the country code and country-specific
trunk prefix.

1. Log in as provider administrator.
#. Select **Dial Plan Management > Advanced Configuration > Dial Plan Schema**.
#. Click the country dial plan schema you want to modify.
#. On the tabs bar, select **Route Lists**.
#. For the route list you want to update, under Members, click **More...**
#. If necessary, click + to expand the Members field.
#. For Called Party Discard Digits, select PreDot.
#. For Called Party Prefix Digits (Outgoing Calls), enter the appropriate trunk
prefix for the country.
#. Click **Save**.

Edit Route Patterns for Called-Party As Dialed Feature
......................................................

If pre-10.6(2) Country Dial Plans have been deployed, edit certain route patterns
to place the country code before the dot in the patterns.

.. important::

Edit all route patterns for all country dial plans deployed for the customer
with the following exceptions:

* Any route pattern that has the digits 04 (emergency), 05 (service), or
11 (operator) immediately before the dot.
* Any route pattern that has the digits 01 (international) immediately before
the dot, unless the country code is specified immediately after the dot.
* Any route pattern that has an X (mask digit) immediately after the dot.

Before You Begin
................

To complete this procedure, you need to know the country code for each country
dial plan deployed for the customer.

1. Log in as provider administrator.
#. Set the hierarchy path to the customer for which you are implementing the As
Dialed feature.
#. Select **Device Management > CUCM > Route Patterns**.
#. Click the route pattern.
#. On the **Pattern Definitions** tab, edit the Route Pattern field.

* If the route pattern contains the country code after the dot, move it to
immediately before the dot.
* If the route pattern does not contain the country code, add it immediately
before the dot.

Example: For Great Britain:

* Change \**001.44! to \**00144.!
* Change \**002.! to \**00244.!

6. On the **Called Party Transformations** tab, change the Prefix Digits
(Outgoing Calls) field from + to +<cc> where <cc> is the appropriate country code.

Example: For Great Britain, change + to +44

#. Click **Save**.

Edit Route Lists for Called-Party As Dialed Feature
...................................................

If country dial plans have been deployed, use this procedure to implement the
Called-Party As Dialed feature.

.. important::

Edit all country-specific route lists for the customer with the following
exceptions:

* Emergency
* International
* Operator
* Service

Before You Begin
................

To complete this procedure you need to know the country-specific trunk prefix.

1. Log in as provider administrator.
#. Set the hierarchy path to the customer for which you want to implement the
Called-Party As Dialed feature.
#. Select **Device Management > CUCM > Route Lists**.
#. Click the route list to edit.
#. Click the + to expand the Route Group Items section.
#. For Called Party Discard Digits, select PreDot.
#. For Called Party Prefix Digits, enter the appropriate trunk prefix for the
country.
#. Click **Save**.