.. _configure_device_pools:
.. rst-class:: chapter-with-expand
How to Configure Device Pools
-----------------------------
**Introduction**
Device pools define sets of common characteristics for devices. The device
pool structure supports the separation of user and location information.
The device pool contains system, device, and location-related information.
After adding a new device pool, you can use it to configure devices such
as Cisco Unified IP Phones, gateways, conference bridges, transcoders,
media termination points, voice-mail ports, CTI route points, and so on.
**Procedure**
1. Log in as provider, reseller, or customer administrator.
2. Perform one of these options:
* If you logged in as provider or reseller administrator,
choose **Device Management > CUCM > Device Pools**.
* If you logged in as customer administrator, choose
**Device Management > Advanced > CUCM > Device Pools**.
3. Perform one of these options:
* To add a new device pool, click **Add**, then go to step 5.
* To edit an existing device pool, click the line item in the
table. Go to step 5.
4. In the popup, choose from the drop-down the network device list (NDL)
to which you are adding the device pool, and click **OK**.
Note:
The NDL popup only appears when you add a new device pool instance. If
you are updating an existing instance, go to Step 5.
If you are adding the instance to a Site hierarchy node, the NDL popup
does not appear. You go right to the Add Device Pool form using the
NDL associated to the site.
5. From the **Device Pool Settings** tab, complete at minimum, the mandatory
:ref:`device_pool_settings_fields`.
6. From the **Local Route Group Settings** tab, complete at minimum, the mandatory
:ref:`local_route_group_settings_fields`.
7. From the **Roaming Sensitive Settings** tab, complete at minimum, the mandatory
:ref:`roaming_sensitive_settings_fields`.
8. From the **Device Mobility Related Information** tab, complete the required
:ref:`device_mobility_related_information_fields`.
9. From the **Geolocation Configuration** tab, complete the required
:ref:`geolocation_configuration_fields`.
10. From the **Incoming Calling Party Settings** tab, complete the required
:ref:`incoming_calling_party_settings_fields`.
11. From the **Incoming Called Party Settings** tab, complete the required
:ref:`incoming_called_party_settings_fields`.
12. From the **Caller ID for Calls from This Phone** tab, complete the required
:ref:`caller_id_for_calls_from_this_phone_fields`.
13. From the **Connected Party Settings** tab, complete the required
:ref:`connected_party_settings_fields`.
14. From the **Redirecting Party Settings** tab, complete the required
:ref:`redirecting_party_settings_fields`.
15. Click **Save**.
The route partition appears in the device pool list.
To modify any of these characteristics, make your changes and click **Save**.
To delete a device pool, select the check box to the left of the **Name** column
in the group list, and click **Delete**.
.. _device_pool_settings_fields:
Device Pool Settings Fields
---------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+--------------------------+-------------------------------------------+
| Option | Description |
+==========================+===========================================+
| | Enter the name of the new device pool |
| | that you are creating. You can enter up |
| | to 50 characters, which include |
| Device Pool Name \* | alphanumeric characters, periods (.), |
| | hyphens (-), underscores (_), and blank |
| | spaces. |
| | |
| | Default value: None |
+--------------------------+-------------------------------------------+
| | Choose the Cisco Unified Communications |
| | Manager group to assign to devices in |
| | this device pool. A Unified CM group |
| Cisco Unified | specifies a prioritized list of up to |
| CM Group \* | three Unified CMs. The first Unified CM |
| | in the list serves as the primary one |
| | for that group. The other members of |
| | the group serve as backup Unified CMs |
| | for redundancy. |
+--------------------------+-------------------------------------------+
| | Choose the calling search space to |
| | assign to devices in this device pool |
| Calling Search Space for | that auto-register with Unified CM. The |
| Auto-registration | calling search space specifies |
| | partitions that devices can search when |
| | attempting to complete a call. |
+--------------------------+-------------------------------------------+
| | From the drop-down list, choose an |
| | existing Calling Search Space (CSS) to |
| | use for the devices in this device |
| | profile as an adjunct CSS for the |
| | Extension Mobility Cross Cluster (EMCC) |
| | feature. To configure a new CSS or |
| | modify an existing CSS, choose **Call |
| | Routing > Class of Control > Calling |
| | Search Space** in Unified CM |
| | Administration. |
| | |
| Adjunct CSS | When configuring the EMCC feature, the |
| | administrator must configure a device |
| | pool for each remote cluster. If the |
| | remote cluster is located in a |
| | different country, the adjunct CSS must |
| | embrace the partition with which the |
| | emergency patterns of that country |
| | associate. This configuration |
| | facilitates country-specific emergency |
| | call routing. |
| | |
| | Default value: None |
+--------------------------+-------------------------------------------+
| | Choose a clusterwide priority setting |
| | for reverted calls that the hold |
| | reversion feature invokes. This setting |
| | specifies which call type, incoming |
| | calls or reverted calls, have priority |
| | for user actions, such as going off |
| | hook. |
| | |
| | * **Default**-If you choose this option, |
| | incoming calls have priority. |
| | * **Highest**-If you choose this option, |
| Reverted Call Focus | reverted calls have priority. |
| Priority | |
| | The **Not Selected** setting specifies |
| | the reverted call focus priority setting |
| | for the default device pool at |
| | installation. At installation, incoming |
| | calls have priority. You cannot choose |
| | this setting in Unified CM. |
| | |
| | Note: This setting applies specifically |
| | to hold reverted calls; it does not |
| | apply to parked reverted calls. |
+--------------------------+-------------------------------------------+
| Intercompany Media | Choose an **Intercompany Media Services |
| Services Enrolled Group | Enrolled Group** from the drop-down list. |
+--------------------------+-------------------------------------------+
.. _local_route_group_settings_fields:
Local Route Group Settings Fields
---------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+-------------+-----------------------------------------------------------+
| Option | Description |
+=============+===========================================================+
| Local Route | From the drop-down, choose the name of the local route |
| Group | group to associate with this device pool. |
+-------------+-----------------------------------------------------------+
| Route Group | From the drop-down, choose the value for the local route |
| | group to associate with this device pool. |
+-------------+-----------------------------------------------------------+
.. _roaming_sensitive_settings_fields:
Roaming Sensitive Settings Fields
---------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+----------------------+-------------------------------------------------+
| Option | Description |
+======================+=================================================+
| | Choose the date/time group to assign to |
| | devices in this device pool. The date/time |
| Date/Time Group \* | group specifies the time zone and the |
| | display formats for date and time. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | Choose the Unified CM region to assign to |
| | devices in this device pool. The Unified CM |
| | region settings specify voice codec that |
| Region \* | can be used for calls within a region and |
| | between other regions. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | From the drop-down list, choose a media |
| | resource group list. A media resource group |
| | list specifies a prioritized list of media |
| | resource groups. An application selects the |
| | required media resource (for example, a |
| Media Resource Group | music on hold server, transcoder, or |
| List | conference bridge) from the available media |
| | resource groups according to the priority |
| | order defined in a media resource group |
| | list. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | Use locations to implement call admission |
| | control (CAC) in a centralized |
| | call-processing system. CAC enables you to |
| | regulate audio quality and video |
| | availability. It works by limiting the |
| | amount of bandwidth that is available for |
| | audio and video calls over links between |
| | locations. The location specifies the total |
| | bandwidth that is available for calls to |
| | and from this location. |
| | |
| Location | From the drop-down list, choose the |
| | appropriate location for this device pool. |
| | |
| | A location setting of **None** or **Hub_None** |
| | means that the locations feature does not |
| | track the bandwidth that the devices in |
| | this pool consume. A location setting of |
| | **Phantom** specifies a location that enables |
| | successful CAC across intercluster trunks |
| | that use H.323 protocol or SIP. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | From the drop-down list, choose the |
| | locale that is associated with phones and |
| | gateways. The network locale contains a |
| | definition of the tones and cadences that |
| | the phones and gateways in the device pool |
| | in a specific geographic area use. Make |
| | sure that you select a network locale that |
| | all of the phones and gateways that use |
| | this device pool can support. |
| | |
| | Note: |
| | |
| | If the user does not choose a network |
| | locale, the locale that is specified in the |
| Network Locale | Unified CM clusterwide parameters as |
| | Default Network Locale applies. |
| | |
| | Note: |
| | |
| | Choose only a network locale that is |
| | already installed and supported by the |
| | associated devices. The list contains all |
| | available network locales for this setting, |
| | but not all are necessarily installed. When |
| | a device is associated with a network |
| | locale that it does not support in the |
| | firmware, the device fails to come up. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+----------------------+-------------------------------------------------+
| Option | Description |
+======================+=================================================+
| | From the drop-down list, choose a |
| | survivable remote site telephony (SRST) |
| | reference to assign to devices in this |
| | device pool. Choose from these options: |
| | |
| | * **Disable** - When you choose this option, |
| | devices in this device pool do not have |
| | SRST reference gateways that are |
| SRST Reference \* | available to them. |
| | * **Use Default Gateway** - When you choose |
| | this option, devices in this device |
| | pool use the default gateway for SRST. |
| | * **Existing SRST references** - When you |
| | choose an SRST reference from the |
| | drop-down list, devices in this device |
| | pool use this SRST reference gateway. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | This setting defines the time that the |
| | Cisco Unified IP Phone monitors its |
| | connection to Unified CM before it |
| | unregisters from SRST and reregisters to |
| | Unified CM. |
| | |
| | To use the configuration for the enterprise |
| | parameter, you can enter "1" or leave |
| | the field blank. The default value for the |
| Connection Monitor | enterprise parameter equals 120 seconds. |
| Duration | |
| | Tip: |
| | |
| | When you change the value of the connection |
| | monitor duration, it applies only to the |
| | device pool that is being updated. All |
| | other device pools use the value in their |
| | own connection monitor duration fields or |
| | use the value that is configured in the |
| | enterprise parameter. |
+----------------------+-------------------------------------------------+
| | This setting determines whether the devices |
| | or phone users in this device pool have |
| | single-button access for barge and cBarge. |
| | From the drop-down list, choose from |
| | these options: |
| | |
| | * **Off** - When you choose this option, the |
| | devices in this device pool have the |
| | Single Button Barge/cBarge feature |
| | disabled. |
| | * **Barge** - When you choose this option, |
| | the devices in this device pool have |
| Single Button Barge | the Single Button Barge feature |
| | enabled. |
| | * **CBarge** - When you choose this option, |
| | the devices in this device pool have |
| | the Single Button cBarge feature |
| | enabled. |
| | * **Default** - When you choose this option, |
| | the devices in this device pool use the |
| | service parameter setting for the |
| | Single Button Barge/cBarge feature. |
| | |
| | Default value: Default |
+----------------------+-------------------------------------------------+
| | This setting determines whether the Join |
| | Access Lines feature is enabled for the |
| | devices or phone users in this device pool. |
| | From the drop-down list, choose from |
| | these options: |
| | |
| | * **Off** - When you choose this option, the |
| | devices in this device pool have the |
| | Join Access Lines feature disabled. |
| Join Access Lines | * **On** - When you choose this option, the |
| | devices in this device pool have the |
| | Join Access Lines feature enabled. |
| | * **Default** - When you choose this option, |
| | the devices in this device pool use the |
| | service parameter setting for the Join |
| | Access Lines feature. |
| | |
| | Default value: Default |
+----------------------+-------------------------------------------------+
| | Select the physical location for this |
| | device pool. The system uses physical |
| | location with the device mobility feature |
| Physical Location | to identify the parameters that relate to a |
| | specific geographical location. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+----------------------+-------------------------------------------------+
| Option | Description |
+======================+=================================================+
| | Device mobility groups represent the |
| | highest level geographic entities in your |
| Device Mobility | network and are used to support the device |
| Group | mobility feature. |
| | |
| | Default value: None |
+----------------------+-------------------------------------------------+
| | Choose a wireless LAN profile group from |
| | the drop-down list. |
| | |
| Wireless LAN Profile | Note: |
| Group | |
| | You can specify the Wireless LAN Profile |
| | Group at the Device Pool level or the |
| | individual phone level. |
+----------------------+-------------------------------------------------+
.. _device_mobility_related_information_fields:
Device Mobility Related Information Fields
------------------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+-------------------------+----------------------------------------------+
| Option | Description |
+=========================+==============================================+
| | Choose the appropriate calling search |
| | space to be used as the device calling |
| Device Mobility Calling | search space when the device is roaming |
| Search Space | and in the same device mobility group. |
| | |
| | Default value: None |
+-------------------------+----------------------------------------------+
| | Choose the appropriate calling search |
| | space for the device to use when |
| | automated alternate routing (AAR) is |
| | performed. The AAR calling search space |
| AAR Calling Search | specifies the collection of route |
| Space | partitions that are searched to |
| | determine how to route a collected |
| | (originating) number that is otherwise |
| | blocked due to insufficient bandwidth. |
| | |
| | Default value: None |
+-------------------------+----------------------------------------------+
| | Choose the automated alternate routing |
| | (AAR) group for this device. The AAR |
| | group provides the prefix digits that |
| | are used to route calls that are |
| AAR Group | otherwise blocked due to insufficient |
| | bandwidth. An AAR group setting of **None** |
| | specifies that no rerouting of blocked |
| | calls is attempted. |
| | |
| | Default value: None |
+-------------------------+----------------------------------------------+
| | This setting allows you to localize the |
| | calling party number on the device. Make |
| | sure that the Calling Party |
| | Transformation CSS that you choose |
| | contains the calling party |
| | transformation pattern that you want to |
| | assign to this device pool. |
| | |
| | Tip: Before the call occurs, the device |
| Calling Party | must apply the transformation by using |
| Transformation CSS | digit analysis. |
| | |
| | Note: |
| | |
| | If you configure the Calling Party |
| | Transformation CSS as **None** for the |
| | device pool and you select the |
| | **Use Device Pool Calling Party |
| | Transformation CSS** check box in the |
| | device configuration window, the |
| | transformation does not match and does |
| | not get applied. Ensure that you |
| | configure the Calling Party |
| | Transformation Pattern in a non-null |
| | partition that is not used for routing. |
| | |
| | Default value: None |
+-------------------------+----------------------------------------------+
| | This setting allows you to localize the |
| | called party number on the device. Make |
| | sure that the Called Party |
| | Transformation CSS that you choose |
| | contains the called party transformation |
| | pattern that you want to assign to this |
| | device pool. |
| | |
| Called Party | Note: |
| Transformation CSS | |
| | If you configure the Called Party |
| | Transformation CSS as **None**, the |
| | transformation does not match and does |
| | not get applied. Ensure that you |
| | configure the Called Party |
| | Transformation pattern in a non-null |
| | partition that is not used for routing. |
| | |
| | Default value: None |
+-------------------------+----------------------------------------------+
.. _geolocation_configuration_fields:
Geolocation Configuration Fields
--------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+--------------------+---------------------------------------------+
| Option | Description |
+====================+=============================================+
| | From the drop-down list, choose a |
| | geolocation. |
| | |
| | You can choose the Unspecified geolocation, |
| Geolocation | which designates that the devices in this |
| | device pool do not associate with a |
| | geolocation. |
| | |
| | Default value: None |
+--------------------+---------------------------------------------+
| | From the drop-down list, choose a |
| | geolocation filter. |
| | |
| Geolocation Filter | If you leave the <None> setting, no |
| | geolocation filter gets applied for the |
| | devices in this device pool. |
| | |
| | Default value: None |
+--------------------+---------------------------------------------+
.. _incoming_calling_party_settings_fields:
Incoming Calling Party Settings Fields
---------------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+------------------------+------------------------------------------------+
| Option | Description |
+========================+================================================+
| | Unified CM applies the prefix that you |
| | enter in this field to calling party |
| | numbers that use **National** for the Calling |
| | Party Numbering Type. |
| | |
| | You can enter up to eight characters, which |
| | include digits, the international escape |
| National Prefix | character (\+), asterisk (*), or the pound |
| | sign (#). You can enter the word "Default" |
| | instead of entering a prefix. If the word |
| | "Default" displays in the **Prefix** field, |
| | Unified CM applies the service parameter |
| | configuration for the incoming calling |
| | party prefix, which supports both the |
| | prefix and strip digit functionality. |
+------------------------+------------------------------------------------+
| | Enter the number of digits, up to the |
| | number 24, that you want Unified CM to |
| National Strip Digits | strip from the calling party number of |
| | National type before it applies the |
| | prefixes. |
+------------------------+------------------------------------------------+
| | This setting allows you to globalize the |
| | calling party number of National calling |
| | party number type on the device. Make |
| | sure that the calling search space that |
| | you choose contains the calling party |
| | transformation pattern that you want to |
| National Calling | assign to this device. Before the call |
| Search Space | occurs, the device must apply the |
| | transformation by using digit analysis. |
| | If you configure the CSS as **None**, the |
| | transformation does not match and does |
| | not get applied. Make sure that you |
| | configure the calling party |
| | transformation pattern in a non-null |
| | partition that is not used for routing. |
+------------------------+------------------------------------------------+
| | Unified CM applies the prefix that you |
| | enter in this field to calling party |
| | numbers that use **International** for the |
| | Calling Party Numbering Type. You can |
| | enter up to eight characters, which |
| | include digits, the international escape |
| | character (\+), asterisk (*), or the pound |
| International Prefix | sign (#). You can enter the word "Default" |
| | instead of entering a prefix. If the word |
| | "Default" displays in the **Prefix** field in |
| | the **Device Pool Configuration** window, |
| | Unified CM applies the service parameter |
| | configuration for the incoming calling |
| | party prefix, which supports both the |
| | prefix and strip digit functionality. |
+------------------------+------------------------------------------------+
| | Enter the number of digits, up to the |
| International Strip | number 24, that you want Unified CM to |
| Digits | strip from the calling party number of |
| | International type before it applies the |
| | prefixes. |
+------------------------+------------------------------------------------+
| | This setting allows you to globalize the |
| | calling party number of International |
| | calling party number type on the device. |
| | Make sure that the calling party |
| | transformation CSS that you choose |
| | contains the calling party transformation |
| | pattern that you want to assign to this |
| International Calling | device. Before the call occurs, the |
| Search Space | device must apply the transformation by |
| | using digit analysis. If you configure |
| | the CSS as **None**, the transformation does |
| | not match and does not get applied. |
| | Ensure that you configure the calling |
| | party transformation pattern in a |
| | non-null partition that is not used for |
| | routing. |
+------------------------+------------------------------------------------+
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+------------------------+------------------------------------------------+
| Option | Description |
+========================+================================================+
| | Unified CM applies the prefix that you |
| | enter in this field to calling party |
| | numbers that use **Unknown** for the Calling |
| | Party Numbering Type. You can enter up to |
| | eight characters, which include digits, |
| | the international escape character (\+), |
| Unknown Prefix | asterisk (*), or the pound sign (#). If |
| | the word "Default" displays in the **Prefix** |
| | field in the Device Pool Configuration |
| | window, Unified CM applies the service |
| | parameter configuration for the incoming |
| | calling party prefix, which supports both |
| | the prefix and strip digit functionality. |
+------------------------+------------------------------------------------+
| | Enter the number of digits, up to the |
| | number 24, that you want Unified CM to |
| Unknown Strip Digits | strip from the calling party number of |
| | Unknown type before it applies the |
| | prefixes. |
+------------------------+------------------------------------------------+
| | This setting allows you to globalize the |
| | calling party number of "Unknown" calling |
| | party number type on the device. Make |
| | sure that the calling party |
| | transformation CSS that you choose |
| | contains the calling party transformation |
| | pattern that you want to assign to this |
| Unknown Calling Search | device. Before the call occurs, the |
| Space | device must apply the transformation by |
| | using digit analysis. If you configure |
| | the CSS as **None**, the transformation does |
| | not match and does not get applied. |
| | Ensure that you configure the calling |
| | party transformation pattern in a |
| | non-null partition that is not used for |
| | routing. |
+------------------------+------------------------------------------------+
| | Unified CM applies the prefix that you |
| | enter in this field to calling party |
| | numbers that use **Subscriber** for the |
| | Calling Party Numbering Type. You can |
| | enter up to eight characters, which |
| | include digits, the international escape |
| Subscriber Prefix | character (\+), asterisk (*), or the pound |
| | sign (#). If the word "Default" displays in |
| | the **Prefix** field in the **Device Pool |
| | Configuration** window, Unified CM applies |
| | the service parameter configuration for |
| | the incoming calling party prefix, which |
| | supports both the prefix and strip digit |
| | functionality. |
+------------------------+------------------------------------------------+
| | Enter the number of digits, up to the |
| Subscriber Strip | number 24, that you want Unified CM to |
| Digits | strip from the calling party number of |
| | Subscriber type before it applies the |
| | prefixes. |
+------------------------+------------------------------------------------+
| | This setting allows you to globalize the |
| | calling party number of **Subscriber** |
| | calling party number type on the device. |
| | Make sure that the CSS that you choose |
| | contains the calling party transformation |
| | pattern that you want to assign to this |
| Subscriber Calling | device. Before the call occurs, the |
| Search Space | device must apply the transformation by |
| | using digit analysis. If you configure |
| | the CSS as **None**, the transformation does |
| | not match and does not get applied. |
| | Ensure that you configure the calling |
| | party transformation pattern in a |
| | non-null partition that is not used for |
| | routing. |
+------------------------+------------------------------------------------+
.. _incoming_called_party_settings_fields:
Incoming Called Party Settings Fields
-------------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+------------------------+-------------------------------------------------+
| Option | Description |
+========================+=================================================+
| | Unified CM applies the prefix that you |
| | enter in this field to calling party |
| | numbers that use **National** for the Called |
| | Party Numbering Type. |
| | |
| | You can enter up to sixteen (16) characters, |
| | which include digits, the international escape |
| National Prefix | character (\+), asterisk (*), or the pound sign |
| | (#). You can enter the word "Default" instead |
| | of entering a prefix. |
| | |
| | Tip: |
| | |
| | If the word "Default" displays in the |
| | **Gateway** or **Trunk Configuration** window, |
| | you cannot configure the **Strip Digits** field |
| | in the Gateway or Trunk Configuration window. |
| | In this case, Unified CM takes the configuration|
| | for the **Prefix** and **Strip Digits** fields |
| | from the device pool that is applied to the |
| | device. If the word "Default" displays in the |
| | **Prefix** field in the **Device Pool |
| | Configuration** window, Unified CM applies the |
| | service parameter configuration for the |
| | incoming called party prefix, which supports |
| | both the prefix and strip digit functionality. |
| | |
| | Tip: |
| | |
| | To configure the **Strip Digits** field, leave |
| | the **Prefix** field blank or enter a valid |
| | configuration in the **Prefix** field. To |
| | configure the **Strip Digits** fields, do not |
| | enter the word "Default" in the **Prefix** |
| | field. |
+------------------------+-------------------------------------------------+
| National Strip Digits | Enter the number of digits, that you want |
| | Unified CM to strip from the called party |
| | number of "Unknown" type before it applies the |
| | prefixes. |
+------------------------+-------------------------------------------------+
| National Calling | This setting allows you to transform the called |
| Search Space | party number of "Unknown" called party number |
| | type on the device. If you choose **None**, no |
| | transformation occurs for the incoming called |
| | party number. Make sure that the calling search |
| | space that you choose contains the called party |
| | transformation pattern that you want to assign |
| | to this device. |
+------------------------+-------------------------------------------------+
| | Unified CM applies the prefix that you enter in |
| | this field to called party numbers that use |
| | **National** for the Called Party Numbering |
| | Type. You can enter up to 16 characters, which |
| | include digits, the international escape |
| | character (+), asterisk (*), or the pound sign |
| | (#). You can enter the word "Default" instead |
| International Prefix | of entering a prefix. |
| | |
| | Tip: |
| | |
| | If the word "Default" displays in the |
| | **Prefix** field in the Gateway or Trunk |
| | Configuration window, you cannot configure the |
| | **Strip Digits** field in the Gateway or Trunk |
| | Configuration window. In this case, Unified CM |
| | takes the configuration for the **Prefix** and |
| | **Strip Digits** fields from the device pool |
| | that is applied to the device. If the word |
| | "Default" displays in the **Prefix** field in |
| | the Device Pool Configuration window, Unified |
| | CM applies the service parameter configuration |
| | for the incoming called party prefix, which |
| | supports both the prefix and strip digit |
| | functionality. |
| | |
| | Tip: |
| | |
| | To configure the **Strip Digits** field, |
| | leave the **Prefix** field blank or enter a |
| | valid configuration in the **Prefix** field. |
| | To configure the **Strip Digits** fields, |
| | do not enter the word "Default" in the |
| | **Prefix** field. |
+------------------------+-------------------------------------------------+
| International Strip | Enter the number of digits that you want |
| Digits | Unified CM to strip from the called party |
| | number of International type before it applies |
| | the prefixes. |
+------------------------+-------------------------------------------------+
| International Calling | This setting allows you to transform the |
| Search Space | called party number of International called |
| | party number type on the device. If you choose |
| | **None**, no transformation occurs for the |
| | incoming called party number. Make sure that |
| | the calling search space that you choose |
| | contains the called party transformation |
| | pattern that you want to assign to this device. |
+------------------------+-------------------------------------------------+
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+------------------------+------------------------------------------------+
| Option | Description |
+========================+================================================+
| | Unified CM applies the prefix that you |
| | enter in this field to called numbers that use |
| | **Unknown** for the Called Party Numbering |
| | Type. You can enter up to sixteen characters, |
| | which include digits, the international escape |
| | character (\+), asterisk (*), or the pound |
| | sign (#). You can enter the word "Default" |
| | instead of entering a prefix. |
| | |
| Unknown Prefix | Tip: |
| | |
| | If the word "Default" displays in the |
| | **Prefix** in the Gateway or Trunk window, |
| | you cannot configure the **Strip Digits** in |
| | the Gateway or Trunk Configuration window. In |
| | this case, Unified CM takes the configuration |
| | for the **Prefix** and **Strip Digits** fields |
| | from the device pool that is applied to the |
| | device. If the word "Default" displays in the |
| | **Prefix** field in the Device Pool |
| | Configuration window, Unified CM applies the |
| | service parameter configuration for the |
| | incoming called party prefix, which supports |
| | both the prefix and strip digit functionality. |
| | |
| | Tip: |
| | |
| | To configure the **Strip Digits** field, leave |
| | the **Prefix** field blank or enter a valid |
| | configuration in the **Prefix field**. To |
| | configure the **Strip Digits** fields, do not |
| | enter the word "Default" in the **Prefix** |
| | field. |
+------------------------+------------------------------------------------+
| Unknown Strip Digits | Enter the number of digits, that you want |
| | Unified CM to strip from the called party |
| | number of "Unknown" type before it applies the |
| | prefixes. |
+------------------------+------------------------------------------------+
| Unknown Calling Search | This setting allows you to transform the |
| Space | called party number of "Unknown" called party |
| | number type on the device. If you choose |
| | **None** no transformation occurs for the |
| | incoming called party number. Make sure that |
| | the calling search space that you choose |
| | contains the called party transformation |
| | pattern that you want to assign to this device.|
+------------------------+------------------------------------------------+
| Subscriber Prefix | Unified CM applies the prefix that you |
| | enter in this field to called numbers that use |
| | **Subscriber** for the Called Party Numbering |
| | Type. You can enter up to sixteen characters, |
| | which include digits, the international escape |
| | character (\+), asterisk (*), or the pound |
| | sign (#). You can enter the word "Default" |
| | instead of entering a prefix. |
| | |
| | Tip: |
| | |
| | If the word "Default" displays in the |
| | **Prefix** field in the Gateway or Trunk |
| | Configuration window, you cannot configure the |
| | **Strip Digits** field in the Gateway or Trunk |
| | Configuration window. In this case, Unified CM |
| | takes the configuration for the **Prefix** and |
| | **Strip Digits** fields from the device pool |
| | that is applied to the device. If the word |
| | "Default" displays in the **Prefix** field in |
| | the Device Pool Configuration window, Unified |
| | CM applies the service parameter configuration |
| | for the incoming called party prefix, which |
| | supports both the prefix and strip digit |
| | functionality. |
| | |
| | Tip: |
| | |
| | To configure the **Strip Digits** field, leave |
| | the **Prefix** field blank or enter a valid |
| | configuration in the **Prefix** field. To |
| | configure the **Strip Digits** fields, do not |
| | enter the word "Default" in the **Prefix** |
| | field. |
+------------------------+------------------------------------------------+
| Subscriber Strip | Enter the number of digits, that you want |
| Digits | Unified CM to strip from the called party |
| | number of Subscriber type before it applies |
| | the prefixes. |
+------------------------+------------------------------------------------+
| Subscriber Calling | This setting allows you to transform the |
| Search Space | called party number of Subscriber called party |
| | number type on the device. If you choose |
| | **None**, no transformation occurs for the |
| | incoming called party number. Make sure that |
| | the calling search space that you choose |
| | contains the called party transformation |
| | pattern that you want to assign to this device.|
+------------------------+------------------------------------------------+
.. _caller_id_for_calls_from_this_phone_fields:
Caller ID For Calls From This Phone Fields
------------------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+--------------------+-----------------------------------------------+
| Option | Description |
+====================+===============================================+
| | From the drop-down list, choose the |
| | CSS that contains the Calling Party |
| Calling Party | Transformation Pattern that you want to |
| Transformation CSS | apply to devices in this device pool. |
| | |
| | When Unified CM receives a call from a device |
| | in this device pool on an inbound line, |
| | Unified CM immediately applies the calling |
| | party transformation patterns in this CSS to |
| | the digits in the calling party number before |
| | it routes the call. This setting allows you |
| | to apply digit transformations to the calling |
| | party number before Unified CM routes the |
| | call. For example, a transformation pattern |
| | can change a phone extension to appear as |
| | an E.164 number. |
+--------------------+-----------------------------------------------+
.. _connected_party_settings_fields:
Connected Party Settings Fields
-------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+--------------------+-----------------------------------------------+
| Option | Description |
+====================+===============================================+
| | This setting is applicable for inbound calls |
| | only. This setting allows you to transform |
| | the connected party number on the device to |
| | display the connected number in another |
| | format, such as a DID or E164 number. Unified |
| | CM includes the transformed number in the |
| | headers of various SIP messages, including |
| | 200 OK and mid-call update/reinvite messages |
| | for SIP calls and in the Connected Number |
| | Information Element of CONNECT and NOTIFY |
| Connected Party | messages for H.323 and MGCP calls. Make sure |
| Transformation CSS | that the Connected Party Transformation CSS |
| | that you choose contains the called party |
| | transformation pattern that you want to |
| | assign to this device pool. |
| | |
| | Note: |
| | |
| | If you configure the Connected Party |
| | Transformation CSS as **None**, the |
| | transformation does not match and does not |
| | get applied. Ensure that you configure the |
| | Calling Party Transformation pattern used for |
| | Connected Party Transformation in a non-null |
| | partition that is not used for routing. |
+--------------------+-----------------------------------------------+
.. _redirecting_party_settings_fields:
Redirecting Party Settings Fields
---------------------------------
.. tabularcolumns:: |p{3.5cm}|p{12cm}|
+--------------------+-----------------------------------------------+
| Option | Description |
+====================+===============================================+
| | This setting allows you to transform the |
| | redirecting party number on the device to E164|
| | format. Unified CM includes the transformed |
| | number in the diversion header of invite |
| | messages for SIP trunks and in the Redirecting|
| Redirecting Party | Number Information Element of setup message |
| Transformation CSS | (for H.323 and MGCP) sent out of Unified CM. |
| | Make sure that the Redirecting Party |
| | Transformation CSS that you choose contains |
| | the called party transformation pattern that |
| | you want to assign to this device pool. |
| | that the Connected Party Transformation CSS |
| | that you choose contains the called party |
| | transformation pattern that you want to |
| | assign to this device pool. |
| | |
| | Note: |
| | |
| | If you configure the Redirecting Party |
| | Transformation CSS as **None**, the |
| | transformation does not match and does not |
| | get applied. Ensure that you configure the |
| | Redirecting Party Transformation CSS in a |
| | non-null partition that is not used for |
| | routing. |
+--------------------+-----------------------------------------------+